v2.1

Minor Versionm

by Jason Fox

GO Anywhere Asset Tracker

Written By: Jason Fox (and 2 other contributors)
  • Comments: 0
  • Favorites: 0

Difficulty

Easy

Sections

1

Introduction

This guide describes how to install a GO Anywhere Asset Tracker.

Video Overview

    • Do not attempt to install, reconfigure or remove any product from a vehicle while the vehicle is in motion or otherwise in operation. All installation, configuration or removal must be done only in stationary vehicles which are securely parked.

    • Attempting to service devices while the vehicle is in motion could result in malfunctions or accidents, leading to death or serious personal injury.

  2. Before installation, make note of the following:

    • Before installation, make note of the following:

    • GO Anywhere device serial number

    • The serial number is printed above the barcode on the sticker on the bottom of the GO Anywhere device

    • Odometer/engine hours

    • Fleet alias/number/ID

    • License plate number

    • VIN

  3. Activate the device by removing the magnetic strip. The green LED light will blink initially, will turn solid when the device is activated. When performing the activation, ensure the device has a clear line of sight to the sky. The activation process may take up to five minutes.

    • Activate the device by removing the magnetic strip.

    • The green LED light will blink initially, will turn solid when the device is activated.

    • When performing the activation, ensure the device has a clear line of sight to the sky. The activation process may take up to five minutes.

    • If the LED turns red for 15 seconds and then turns off, the activation was unsuccessful.

    • To attempt another activation, re-apply the magnetic strip below the LED (ensuring that you don't cover the LED). Leave the magnetic strip in place for at least 5 seconds and then remove it.

  4. Find a suitable location to install the device on your asset.

    • Find a suitable location to install the device on your asset.

    • The GO Anywhere must have optimal line of sight to the sky with no metal obstructions that interfere with the signal.

  5. Secure the device by using 3 self tapping screws.

    • Secure the device by using 3 self tapping screws.

    • Before drilling, check behind the mounting location to ensure the area is clear of any obstructions or electrical wires/components.

  6. Fasten the 3 magnetic feet in place using the magnetic screws and install the magnet covers. Once complete, install the device on your asset.

    • Fasten the 3 magnetic feet in place using the magnetic screws and install the magnet covers.

    • Once complete, install the device on your asset.

  7. Place the serial number sticker in a suitable location for future reference

    • Place the serial number sticker in a suitable location for future reference

    • To do this, use needle nose pliers.

  9. Enter the installer information.

    • Enter the installer information.

  10. Enter the device serial number.

    • Enter the device serial number.

    • If possible, use the barcode scan feature.

  11. If the device status shows as FAILED, try reapplying the magnetic strip to attempt another authentication. Press Refresh to check the status again.

    • If the device status shows as FAILED, try reapplying the magnetic strip to attempt another authentication.

    • Press Refresh to check the status again.

    • Refer to this link for detailed instructions.

  12. Enter all applicable vehicle information.

    • Enter all applicable vehicle information.

    • Read and acknowledge Geotab's Privacy policy.

  13. If the installation check finishes without errors, a Success! message appears. Press New installation to check another installation, or press Exit when done.

    • If the installation check finishes without errors, a Success! message appears.

    • Press New installation to check another installation, or press Exit when done.

    • If the installation check encounters any errors, an Error message appears.

    • Select New installation to check another installation or press Exit when done.

    • For the latest version of the Limitations of Use, please visit: http://goo.gl/k6Fp0w

    • This product does not contain any user-serviceable parts. Configuration, servicing, and repairs must only be made by an authorized reseller or installer. Unauthorized servicing of these products will void your product warranty.

    • The simplified EU declaration of conformity referred to in Article 10(9) shall be provided as follows:

    • Hereby, Geotab (Address: 2440 Winston Park Drive, Oakville, Ontario L6H 7V2, Canada, Phone number: 1 (877) 436-8221) declares that the radio equipment type ‘telematics device’ is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available here.

    • WARNING: Cancer and Reproductive Harm

Finish Line

Author

with 2 other contributors

Jason Fox

Member since: 09/14/2023

27 Guides authored

Team

Field Service Specialists Member of Field Service Specialists

8 Members

68 Guides authored